CSC270 Lab 11 2011

From dftwiki3
Revision as of 22:11, 10 April 2011 by Thiebaut (talk | contribs) (Created page with "--~~~~ ---- __TOC__ =Designing a 1-bit input I/O controller= Today you have a simple design to implement, but you should make sure you go through the steps ''carefully'', as a ...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

--D. Thiebaut 22:11, 10 April 2011 (EDT)


Designing a 1-bit input I/O controller

Today you have a simple design to implement, but you should make sure you go through the steps carefully, as a flaw in the design could kill some of the kit's components.

This lab assumes that you have assembled, designed and fully tested the 1-bit output controller from Lab #10.


Step 1: Basic Design

Complete the address decoding part of the schematics below, using the approach we took during the class period.

6811 input incomplete.png

Connect the E and address bits to the decoder the exact same way you did in the last Lab, so that you will not have to change the wiring on your kit.

What hexadecimal address did you assign to your flipflop in lab 9?____________

What Yi output is activated by this address? _________

This is the same address we will use for your 1-bit input. We can use both addresses because in the new design the output port (flipflop) is energized only when R/W is low (the processor writes the bit to the flipflop), and the input port you are building tonight will be energized only when R/W is high (the processor will read the bit generated by the switch).

Draw the timing diagrams for a STAA XXXX and a LDAA XXXX instruction, where XXXX is the address you picked for the I/O port. Make sure you show E, the Address bus, R/W, D0, the clock input of the flipflop, and the active-low enable of the tri-state driver.

Step 2: Wiring

Rewire your kit so that it matches your design. HOWEVER, DO NOT CONNECT THE OUTPUT OF THE TRI-STATE DRIVER TO D0. We will do this only when we are sure your circuit is wired correctly. You have several tri-state drivers available to you to choose from:

74240.png 74244.png 74541.png

Pick the one that works best for your design.

Step 3: Programming

Write an endless loop that will constantly read a byte at the address corresponding to your 1-bit input port, and write it back at the same address, storing it in the 1-bit flipflop.

Assemble the program, and enter it in your kit.

Run the program.

Use the scope and verify that the Yi output of the decoder that you are currently using for your 1-bit flipflop is energized by your program. It should look something like this:

6811IO3 bottom.jpg

Monitor the R/W signal as well, and watch both the Yi output and R/W'. You should observe something similar (though not exactly equal) to the following picture:

6811IO1.jpg

Explain why you see a R/W pulse only every other Yi pulse. Make sure you indicate which signal is which on your scope screen-captures!


Step 4: First-Phase Testing

Do NOT connect the output of the driver to D0 yet!

Connect the enable input(s) of your driver to the oscilloscope and observe it/them along with R/W and your Yi signal (use 3 probes). Verify that your driver is turned ON only when R/W is high and Yi is low. You shouldn't connect the data output of your driver to the data bus (bit D0) until you are sure that the gate is activated at the correct time, under correct conditions. Failure to do this will result in the destruction of some chips (either the ones on your breadboard, or the ones inside the kit), so, please, be careful!


Step 5: Connection to Data-Bus

Once you have observed and verified the correct timing of the signals, connect the output of the driver to D0, and its input to one of the switches.

Activate the switch (you might want to use a tiny screwdriver), and verify that the LED turns ON or OFF according to the position of the switch, as we should expect.


Step 6

A bit of programming: Write a program that makes the LED blink (choose whatever blinking frequency you wish) when the switch is in one position, and that turns the LED OFF when the switch is in the opposite position.

Again, demonstrate the correct operation of your program, please!