Tutorial: Arduino and XBee Communication

--D. Thiebaut 17:47, 9 April 2012 (EDT)

---

This page shows how to quickly test the connection and good operating conditions of two XBee modules.

Setup

The setup is simple:

Windows PC <---USB-cable---> Xbee (receiver) <--wireless--> XBee (Xmitter) <---> Arduino

• Instead of a pure Windows machine, we're using a MacPro running Windows in Parallels. This is our Windows machine.
• Windows is connected to an XBee via a USB cable.
• Windows run the X-CTU software that interacts with the XBee. This XBee is in receiving mode.
• An Arduino is connected to the MacPro. The Arduino is connected via 4 wires to another XBee module. This XBee module works in transmit mode.
• The Arduino sends a character of the alphabet to the XBee every second. First 'A', then 'B', all the way to 'Z', then 'A' again, ad infinitum.

Testing XBees on the Windows PC

150px

• Note: The 2 XBee modules are purchased from ADAFruit.com
• Testing steps:
  • Downloaded X-CTU software from ladyada.net
  • X-CTU upgraded itself once started
  • Followed the directions from the configure page at ladyada.net
    • Module #1:(marked with "1" in silver marker on square near antenna)

 Communication with modem. OK
 Modem type = XB24
 Modem firmware version = 10EC

 Serial Number = 13A2004078E552

• • • Following steps from the configure page, reset the baud rate to 19200, and upgraded to most recent firmware.

• • • Module #2:(marked with "2" in silver marker on square near antenna)

 Communication with modem. OK
 Modem type = XB24
 Modem firmware version = 10EC

 Serial Number = 13A2004078E642

• • • Following steps from the configure page, reset the baud rate to 19200, and upgraded Module 2 to most recent firmware.

Testing Arduino

• Install Arduino IDE on 2nd computer (a MacPro)
• Launch Arduino app IDE
• Connect Arduino board to MacPro via USB cable.
• Use the Tools menu to set the model to Diecimila and the USB port to the appropriate port.
• To test normal operation, open the Blink program from the examples (available via the File menu):

/*
  Blink
  Turns on an LED on for one second, then off for one second, repeatedly.
 
  This example code is in the public domain.
 */

void setup() {                
  // initialize the digital pin as an output.
  // Pin 13 has an LED connected on most Arduino boards:
  pinMode(13, OUTPUT);     
}

void loop() {
  digitalWrite(13, HIGH);   // set the LED on
  delay(1000);              // wait for a second
  digitalWrite(13, LOW);    // set the LED off
  delay(1000);              // wait for a second
}

• Upload to Arduino
• Verify that the LED blinks.

Connection of Arduino to XBee

Hardware

• Very simple connections from Arduino to XBee with 4 wires:

Arduino	<--->	XBee
+5V	<--->	+5V
GND	<--->	GND
Digital Pin 2	<--->	TxD
Digital Pin 3	<--->	RxD

Software

• Use the Arduino SoftwareSerial page on the SoftwareSerial library. Great reference for figuring out how Arduino can talk to XBee via a serial port.
• Created Arduino program in IDE:

/*
  Xbee1
  D. Thiebaut
  
  Makes Arduino send 1 character via XBee wireless to another XBee connected
  to a computer via a USB cable. 

  The circuit: 
  * RX is digital pin 2 (connect to TX of XBee)
  * TX is digital pin 3 (connect to RX of XBee)
 
  Based on a sketch created back in the mists of time by Tom Igoe
  itself based on Mikal Hart's example
 
*/

#include <SoftwareSerial.h>

SoftwareSerial xbee(2, 3); // RX, TX
char c = 'A';
int  pingPong = 1;

void setup()  {
   Serial.begin(57600);
   Serial.println( "Arduino started sending bytes via XBee" );

   // set the data rate for the SoftwareSerial port
   xbee.begin( 19200 );
}

void loop()  {
  // send character via XBee to other XBee connected to Mac
  // via USB cable
  xbee.print( c );
  
  //--- display the character just sent on console ---
  Serial.println( c );
  
  //--- get the next letter in the alphabet, and reset to ---
  //--- 'A' once we have reached 'Z'. 
  c = c + 1;
  if ( c>'Z' ) 
       c = 'A';
  
  //--- switch LED on Arduino board every character sent---
  if ( pingPong == 0 )
    digitalWrite(13, LOW);
  else
    digitalWrite(13, HIGH);
  pingPong = 1 - pingPong;
  delay( 1000 );
}

• Compiled program.
• Uploaded program to Arduino.
• In Windows use X-CTU software and click on Terminal Tab to monitor data received wirelessly from Arduino.

• On Arduino side, in IDE, uses Tools menu and opened the console window to see Arduino print characters as they are sent:

It works!

• Observe video. Notice the characters of the alphabet appearing once a second in both windows. One is the console, attached to the transmitting Arduino, the other one is the Terminal window of the X-CTU software on the Windows side, receiving the characters sent wirelessly.